EPG channel is not exist

[peterpeete]

When I tried to put the epg channel guide I have a message EPG channel is not exist

This message is because the bin is corrupt for the Nimiq 91,
also impossible ton scan the satellite, it's normal no SD found...

Does anybody know how to fix this for bev...

Thank you...

[dishuser]

everything is moving to mpeg4 and turbo so you're sol

[peterpeete]

Hello,
What is you're sol
I don't know what...

did you know how to have a epg channel more 1 hour...
more explication...
Thank you...

[nobodyspecial]

Sol sh*t out of luck

[UNVMYRZR]

everything is moving to mpeg4 and turbo so you're sol

I have recently lost almost all channels. Signal is good on 91/82. With everything going to mpeg4 and turbo does that mean my T5 can't get tv anymore and turned into a paper weight?

[auggie]

I have recently lost almost all channels. Signal is good on 91/82. With everything going to mpeg4 and turbo does that mean my T5 can't get tv anymore and turned into a paper weight?

Most likely, the T5 & HD can't handle the changes going on with-out a Re-write of Software/Firmware
and being that Support ended a long time ago, It's not likely to happen. ?

[cappercan]

Explaine how you get a 7 day epg on DL T5 when channel 1522 does not exist anymore?
Tried leaving it on 1012 with guide up on tv and nothing will update.

[jets]

If you think you found a channel that will update the guide please post the TP information for the channel. When on the channel watching a picture just hit OK. The TP frequency and the polarity will be displayed at the top of the popup list.

[jets]

It appears I may have found a 44 hour guide on TP 12428, vertical. One channel is 1199 (NTV).

[dsd]

Channel 1199 (ntv) was my go to channel forever , Then the change happened everything stopped on 91w Today I went into Installation then Manual scan TP 1 then down to frequency and changed it to TURBO 8PSK and back up to TP and changed it to 2 then back down to frequency and changed to Turbo. The signal went up to 97% and 98% but still red I did this for all 31 TP lol.went back to channel 1199(ntv) low and behold it was working. I checked 27 TP and 14 are now coming in and 12 are not. So its better then before when nothing on 91w was coming in..But my EPG is now loading ,way better then two slot. JUst some thing I thought I would pass on...

[peterpeete]

This solution does't work now,
all channel (sd) to nimiq 91 is indicated Bad No Signal,
does somebody have another solution,
thank you...

[jets]

rescan sat 91 TP12428 set as turbo and 21500 SR.

[auggie]

This solution does't work now,
all channel (sd) to nimiq 91 is indicated Bad No Signal,
does somebody have another solution,
thank you...

If you are using a T5 & Getting the Bad/No Signal Message on TV screen, it is most likely your Power Adapter is Failing
Change the adapter to one 12v 3.5-6amp for the T5 to operate correctly

[jets]

auggie, for what ever reason TP 12428 set Turbo, SR21500 is getting signal after rescan. Buddy did it last night and got 1199 back.

But with server down hard to test right now.

[peterpeete]

Hello,
can you put a pictures,
nothing to do when I scan nimiq 91 he don't find no channel
So, I'm not sure If I understand
also before 1week everything is correct,
thank you...

[jets]

No I can't post pictures. Use manual scan and edit TP 12428 on sat 91 as Trurbo8PSK, 2/3 FEC, then hit red button.

[peterpeete]

Hello, when you write edit TP 12428 on sat 91

the TP do you mean set, the name is it Frequency and set to 12.428 ghz (V)

Impossible to scan nimiq 91 no channels found,

Just one thing I use a spliter is it a problem, does I scan with no splitter, directly to nimiq 91

Thank you...

[jets]

You mean you use a switch?

Go Menu > Manual Scan > Select satellite 91.0W > change frequency to 12.428 >change symbol rate to 21.500 by typing in numbers > scroll down to Transmission and change the mode to TURBO 8PSK. Then hit the red scan button. You will now have a few channels with guide if you sit on that channel for 5 minutes. One channel is 1199 or just 199 NTV.

[dsd]

Jets Thanks a lot for this post My go to channel was 1199 for EPG, then it went away. Saw your post and changed symbol rate to 21.500 by typing it in and just exited the screen and now 1199 is working again...TP #13 and 14 work for 21.500ms ...Thanks

[peterpeete]

Hello DSD,

Yes very good I retreive 1199 and some channels to nimiq 91,

Is it possible to have more channels...

Thank you...

[auggie]

Hello DSD,

Yes very good I retreive 1199 and some channels to nimiq 91,

Is it possible to have more channels...

Thank you...

Have you made the changes to TP's 1-thru-19 yet, if not you need to do that for Some channels to come in/back

[beefcake]

Hi i can change the TP but when i go to change the symbol to 21500 it says same TP exist try again i like to get 1199 also thanks

[auggie]

Hi i can change the TP but when i go to change the symbol to 21500 it says same TP exist try again i like to get 1199 also thanks

You need to change the Pol also, H or V and for some the Fec=3/4 or 3/4A

I believe the Dreamlinks are Toast, because it can't handle the TP changes, especially the FEC to 3/4A

No such setting/item in the software/firmware etc.

[jets]

You need to change the Pol also, H or V and for some the Fec=3/4 or 3/4A

I believe the Dreamlinks are Toast, because it can't handle the TP changes, especially the FEC to 3/4A

No such setting/item in the software/firmware etc.

The dreamlinks are fine on 82 and the 91 TP transponder, all that is needed to get HD channels with guide.

[dsd]

This is what I did...Went Menu then Manuel scan, Fist one 91wNimiq 1, Frequency 1 thru 32 and changed each TP to Symbol rate to 21500 ms by using remote to manual type new MS rate in. then transmission rate to Turbo 8PSK on all 32 TPs and Fec to auto. Just exit and it will save all changes for you.

[auggie]

Only TP's 1-thru-19 need changing to 21500 Turbo 8PSK Fec=3/4A

On Lynsat TP's 20-thru-32 are set at 20000 DVB-S Fec=7/8 ?