Sonicview 8000 transponder please HELP

[guy]

I keep loosing signal on 91w worked ok for a while now most lower v polarity in lower # tp stopped working-no signal
boot loader 2.07 main software hd20 front software vb07 setings are rite new power supply new quad lnb changed wires

[The Noof]

Are you watching the 82 as well?If so, remove the 8psk &go through the factory tuner.

[guy]

yes it seems when I get one sat ok the other one looses half the transponers

[guy]

so hooked up another box with no hd module same problem
have anew dp+ quade on port 1 most horizontal transponders work but no V
hooked to the dish with no switches any ideas ????

[dishuser]

so hooked up another box with no hd module same problem
have anew dp+ quade on port 1 most horizontal transponders work but no V
hooked to the dish with no switches any ideas ????
the quad has built in switch
what are your settings?

[guy]

sym 20000
pol h works q 100
v nosig
Fec auto
mode QPSK
Thanks I am going nuts 2 days now

lb type ocs-dp
freq 11250
diseqc off will work on 1 also
legacy switch off

[dishuser]

sym 20000
pol h works q 100
v nosig
Fec auto
mode QPSK
Thanks I am going nuts 2 days now

you need to set lnb and switch in settings

[guy]

to what it now OCS_DP
Legacy off
tried lots off combination this is the only one that works

[nobodyspecial]

try 91 port 1
82 port 2
diseq on for both sats

[Ftafixsat]

For the transponder not coming in, create a new one with same number and change horizontal to vertical or vertical to horizontal and check quality on signal.

[guy]

when you change the vertical to hor or auto shows 97 quality but when you go to chanels show no sig just like it was setup before
no signal on vertical chanels I have two boxes 8000s both the same tried 3 diferent lnbs two new

[dishuser]

post your settings using dp quad

[guy]

Now have a 1000.2 lnb set up 91 Diseqc port1
82 Diseqc port 2
same thing happening

[dishuser]

try switching ports just in case

[Ftafixsat]

When you get quality after change to hor, you can do a scan on the transponder.

[guy]

to Fixsat after changing it shows quality in the transponder fill buy when you do a chanel selection no quality none.
For dishuser tried that doesnt work

[guy]

Ok the problem is when I load the Ihub no chk file it screws the v transponder
if I load the system clean file then everything works perfect but when I load the 20 20 file it screws the v transonders

[The Noof]

Did you try the 2028 I sent you?

[guy]

yea thats the one sory I said 20 20

[guy]

I have one good 8000 that works fine is there a possibility of cloning from the good one and how do you do that ???????????

[The Noof]

I have one good 8000 that works fine is there a possibility of cloning from the good one and how do you do that ???????????

Yes there is...I will send it when I get home.You will need an rs232 cable to do so I believe.I haven't done it in some time.

[guy]

I have the cable same one as you yous to conect the dongle is it not ???

[The Noof]

I have the cable same one as you yous to conect the dongle is it not ???

Cloning is done via the rs232 if I recall correctly.I'm at work, far away from my sat stuff.

[auggie]

Cloning a SV8000 TO Another SV8000 Have the Master Box power "ON" and the Slave box power "OFF" completely.
Connect Master and Slave box with "Null Modem Cable". Use Remote control and pointing at Master and press YELLOW button
and #4 (#1=Main software, #2=Channel List, #3 Bootloader, #4=ALL) Now power up Slave Box with rear power switch and you
should see it start transferring over. Wait until it finishes and reboots.

GOOD LUCK.

[The Noof]

Cloning a SV8000 TO Another SV8000 Have the Master Box power "ON" and the Slave box power "OFF" completely.
Connect Master and Slave box with "Null Modem Cable". Use Remote control and pointing at Master and press YELLOW button
and #4 (#1=Main software, #2=Channel List, #3 Bootloader, #4=ALL) Now power up Slave Box with rear power switch and you
should see it start transferring over. Wait until it finishes and reboots.

GOOD LUCK.

Can also be done with the SV Loader software .Still requires the 232 cable.Depending on the cable you have, you may need a gender changer as well.

[guy]

where do i get the loader
and thanks so much

[The Noof]

https://www.satfix.to/showthread.php?119198-SV8000HD-Loader-Program