Dreamlink T4 on new file

[swan]

put in new file for HD channels (Dreamlink_T4_0113_0308P), installed a DL100 module back when all the change happened in Aug. settings show no 129 echo 5 only shows 129 ciel 2. Do i need a sat file ?

Also menu and channels starts moving by themselves . if i scroll up a channel it will start climbing up by itself . same thing in menu change to the next page and off it goes running though the whole menu.

going to re d/l file and reload and see what happens ... Anyone else see this ?

[nobodyspecial]

129 ciel 2 is 129
did you factory set after loading?

[swan]

yes i did

went to a reload the file again which i did and box is super hot , reason why i think the channel hop is happening

[nobodyspecial]

yes i did

went to a reload the file again which i did and box is super hot , reason why i think the channel hop is happening

get a laptop cooler

[swan]

ok back at it today . double checked the dish today and is hitting 129 fine. well in the setting as follows

129 ciel 2
power - on
type - ocs-dp
freq - 11.250
22 khz - off
sw 1.0 - 3
sw 1.1 - off
leg sw - off

s - red bounce 6% - 97%
q - red steady 97%
NO 129 in blue on top

scanning it finds a few 100 channels s/q will turn blue on tp's it finds channels . When you go to a channel info box on top shows 129 and signal shows blue at 90% but nothing comes in

Where to go next ????? or is it server issues ?????

[nobodyspecial]

ok back at it today . double checked the dish today and is hitting 129 fine. well in the setting as follows

129 ciel 2
power - on
type - ocs-dp
freq - 11.250
22 khz - off
sw 1.0 - 3
sw 1.1 - off
leg sw - off

s - red bounce 6% - 97%
q - red steady 97%
NO 129 in blue on top

scanning it finds a few 100 channels s/q will turn blue on tp's it finds channels . When you go to a channel info box on top shows 129 and signal shows blue at 90% but nothing comes in

Where to go next ????? or is it server issues ?????
has to be blue A new updated tp list was just posted in general receiver forum Check the info

[swan]

ok I check and found this info. All these tp's I have and all show 129 in blue s/q & on top (with others that stay red) in the Manual Scan only . Still not showing blue in the dish settings


129w conus TP's listed by tp number & frequency
17-12457 V SR 21500 FEC 2/3 T8PSK
18-12472 H SR 21500 FEC 2/3 T8PSK
19-12486 V SR 21500 FEC 2/3 T8PSK
20-12501 H SR 21500 FEC 2/3 T8PSK
21-12516 V SR 21500 FEC 2/3 T8PSK
22-12530 H SR 21500 FEC 2/3 T8PSK
23-12545 V SR 21500 FEC 2/3 T8PSK
24-12559 H SR 21500 FEC 2/3 T8PSK
25-12574 V SR 21500 FEC 2/3 T8PSK
26-12588 H SR 21500 FEC 2/3 T8PSK > (12589)
27-12603 V SR 21500 FEC 2/3 T8PSK
28-12618 H SR 21500 FEC 2/3 T8PSK
29-12632 V SR 21500 FEC 2/3 T8PSK
30-12647 H SR 21500 FEC 2/3 T8PSK
31-12661 V SR 21500 FEC 2/3 T8PSK
32-12676 H SR 21500 FEC 2/3 T8PSK

[nobodyspecial]

ok I check and found this info. All these tp's I have and all show 129 in blue s/q & on top (with others that stay red) in the Manual Scan only . Still not showing blue in the dish settings


129w conus TP's listed by tp number & frequency
17-12457 V SR 21500 FEC 2/3 T8PSK
18-12472 H SR 21500 FEC 2/3 T8PSK
19-12486 V SR 21500 FEC 2/3 T8PSK
20-12501 H SR 21500 FEC 2/3 T8PSK
21-12516 V SR 21500 FEC 2/3 T8PSK
22-12530 H SR 21500 FEC 2/3 T8PSK
23-12545 V SR 21500 FEC 2/3 T8PSK
24-12559 H SR 21500 FEC 2/3 T8PSK
25-12574 V SR 21500 FEC 2/3 T8PSK
26-12588 H SR 21500 FEC 2/3 T8PSK > (12589)
27-12603 V SR 21500 FEC 2/3 T8PSK
28-12618 H SR 21500 FEC 2/3 T8PSK
29-12632 V SR 21500 FEC 2/3 T8PSK
30-12647 H SR 21500 FEC 2/3 T8PSK
31-12661 V SR 21500 FEC 2/3 T8PSK
32-12676 H SR 21500 FEC 2/3 T8PSK

if all those show blue in manual scan you should be good. It could be a server issue

[swan]

ok i went thought the list of tps in the manual scan and removed all the old SR 20000 that shows red and now in dish settings i have a blue 129 on top ! going to delete all channels and re scan everything and see ...