Jyazbox v21 hd

[monkeyu]

Hi does anyone no how to down load the epg?
Does anyone no how to change the new tp to 110.119.129.91.82
Just got it and looking for some help . Guy sad just plug in and find satellites so i did on my motech sg2100 motor. Sad I didn't get any manual with it tho. Any advice would be great. Great to see satfix back!!!:)

[Anubis]

Moved your post here as I know that it was not a typo on the brand as I have seen the Jyazbox on fleebay. The box is some sort of clone hybrid or a actual Jynxbox clone unit that was mass produced with the wrong branding in my opinion. Hopefully someone will come along and help you out. I haven't seen a 3rd party file for it yet either.

[iq180]

Hi does anyone no how to down load the epg?
Does anyone no how to change the new tp to 110.119.129.91.82
Just got it and looking for some help . Guy sad just plug in and find satellites so i did on my motech sg2100 motor. Sad I didn't get any manual with it tho. Any advice would be great. Great to see satfix back!!!:)
It should be about the same as all the other V model jynxboxes, press the menu button and take a pic of it and post it so I can see
if it's the same.

[mechanicman]

V21 comes already loaded with clone software.. Just factory reset receiver.. set time zone...set up each satellite such as 119.. then at bottom of that setup page you scan ... but with networks on...
then set up your server
dont do blind scan..

[monkeyu]

No blind scan u say. manual scan instead ? If I do factory rest, then I'll have to refine all my sats with my motor again. Do u no the newest tp for sats I have mechaniceman? Bec I did blind scan

[monkeyu]

Iq180 I'll post some pics tomorrow

[monkeyu]

How do I post pictures here on my Samsung cell?

[mechanicman]

I done a bunch of these boxes... but in your case i would just go to lets say 119 sat and edit transponders...then delete all transponders except for first one.. 12224v 20000

then save and do the scan with networks on.
it will put in all the correct transponders...
blind scan will usually give duplicates channels...never recommended for diknet

[mechanicman]

By the way, to delete transponders just go to installation...manual scan and then you can delete or add or edit transponders

[monkeyu]

2492324924249252492624927

Here u go iq180

[iq180]

2492324924249252492624927

Here u go iq180
Ok, that's the same menu as all the other V model jynxboxes, so it will setup the same way.
So now where are we with the setup and what do you need help with first.
BTW, you don't need to load any software, it has all you need on it.

[monkeyu]

well i actually need alot help lol. this is were i am right now! Dish motor i have it on diseqc 1.2 Well i had to move dish motor to get 110, Had to move it and then play with the tp till i found signal, I saved it and scanned it with blind scan and with network on, The signal is 64 only. So then i did the same thing to find 119 and the signal is 85, same ways again to get 129 and its close to 119 and its signal is 85, also same way for 91 and 82. But now its all mess. I change it to 307 on 110, It moves to bell, press last button ,back on remote it goes back to 110, What do i do? I try and do epg and it doesnt, bounces to 110, or 119 when i press blue epg button the screen says. Id like to no maybe i am save sats wrong in my settings. Also tps id like to no if i have to change them in the setting to 8psk or qpsk. sorry i ask lots question in this quick reply. I no there will be more questions down the road. Answer 1 step at time till we figure it out. thx all :)

[iq180]

well i actually need alot help lol. this is were i am right now! Dish motor i have it on diseqc 1.2 Well i had to move dish motor to get 110, Had to move it and then play with the tp till i found signal, I saved it and scanned it with blind scan and with network on, The signal is 64 only. So then i did the same thing to find 119 and the signal is 85, same ways again to get 129 and its close to 119 and its signal is 85, also same way for 91 and 82. But now its all mess. I change it to 307 on 110, It moves to bell, press last button ,back on remote it goes back to 110, What do i do? I try and do epg and it doesnt, bounces to 110, or 119 when i press blue epg button the screen says. Id like to no maybe i am save sats wrong in my settings. Also tps id like to no if i have to change them in the setting to 8psk or qpsk. sorry i ask lots question in this quick reply. I no there will be more questions down the road. Answer 1 step at time till we figure it out. thx all :)
First thing, never do a blind scan on a provider like DN or b3v, and never use network on, and use Diseq 1.0, the other have never
worked well with an HH motor.

[monkeyu]

Oh ok . SO should I do factory rest then?

[iq180]

Yes, but you mite want to save your server info.

[monkeyu]

Ok thx I'll try it and report back tomrrow .

[jets]

just park on channel 239 for 5 minutes.

[Avetter]

On most receivers to get the new tp you need to do a NETWORK scan. You will find that in the menu somewhere but you may need to dig a big. Network scanning MUST be turned on or it will not pick up the new tp.