Mixed up channels 119 / Bev

[steiner01]

Hey everyone ,

Im not using Bev anymore and my guide is still showing most of Bevs channels on my 119 sat

Is there any way to cancel out all the Bev channels ?

Thanks

[torpainter]

Hey everyone ,

Im not using Bev anymore and my guide is still showing most of Bevs channels on my 119 sat

Is there any way to cancel out all the Bev channels ?

Thanks

hit the sat button and select dish

[steiner01]

hit the sat button and select dish

Thanks for reply Torpainter , I tried that , it didn't work , I still have Bell channels on my Epg Guide ,

Any other suggestions?

[hutch]

select a bev channel... go into channel manager....rename should be highlighted... using your arrows on remote scroll over to delete.... it will default to ch del... hit the yellow button(del option) on remote twice so it reads sat del... a bev sat should already be highlighted so you can hit the blue button on remote & delete it...

[Hunter11]

Factory reset and rescan, probably time you did as channels are moved and transponders are updated from time
to time.

[whoknows]

If you are showing bev channels on 119 then your antenna settings and or dish is a little off. When in 119 antenna settings you must have a lock on satellite. That is usually confirmed by 119 being shown at top of page. If it says 91 then that's where the dish is aimed.

[steiner01]

Factory reset and rescan, probably time you did as channels are moved and transponders are updated from time
to time.

Thanks Hunter11, I will try Factory reset , Will I have to enter all the Files and set it up from scratch after I do that ? Its been a couple of years since I did ....

[steiner01]

Factory reset and rescan, probably time you did as channels are moved and transponders are updated from time
to time.

Thanks Hunter11 , I will try Factory reset , Will I have to re enter the Files and start from scratch ? I haven't done it in a couple of years ...

[Glatt]

Yes just make sure that you reset network off of Dream!!

[Hunter11]

Factory default will erase your sat info and any switch info only, simply factory set, rescan each sat you had previously.Your switch settings should match the sat you choose,(see post #6) the correct sat will appear to match the sat selected with good signal. Any issues, come on back for some help.
Thanks Hunter11, I will try Factory reset , Will I have to enter all the Files and set it up from scratch after I do that ? Its been a couple of years since I did ....

[Hunter11]

Yes just make sure that you reset network off of Dream!!

Factory reset should not affect his network info. Should check in the event it does and re enter the info under Dream. Some receivers will retain this info while others do not.

[hutch]

the nano premium will not dump the network info however it will default to nano stream so be sure to reset it to dream after default

[steiner01]

Ok it worked , bev channels are gone ..

Now it wont let me scan in the 119.


the 110 scanned in , I tried two different switches now , ive never had an issue with 119 before ...

info

Sat ; echo 14ku
diseqc; 3
diseqc 1.1 ; none
tp frequency ; 12297
lnb; 11250
22khz ; off
multi disc switch ; off
search options ; all channels
lnb power ; on

info

Sat ; echo 10/11
diseqc; 1
diseqc 1.1 ; none
tp frequency ; 12224
lnb; 11250
22khz ; off
multi disc switch ; off
search options ; all channels
lnb power on

[hutch]

try bypassing the switch & run the 119 direct to the receiver... If it still doesn't come in you have a bad cable or connector or an LNB thats gone south if you'll excuse the pun or the dish is out of alignment

[Hunter11]

Double check your settings particularly your diseqc port, are you seeing the banner for your sat in that screen with good signal and quality?

[steiner01]

Double check your settings particularly your diseqc port, are you seeing the banner for your sat in that screen with good signal and quality?

Thanks for reply Hunter11 , Yes , I checked the Diseqc port , I managed to scan it in by running the 119 directly to the receiver as Hutch suggested ,

Now only the sat I connect to diseqc 1 works , and it only works on diseqc 1 port on Both the switches I tried ,

so basically I can only watch one sat ....

Maybe Both switches are both Fried ???

suggestions? I have strong signal on both 119 and 110

[Hunter11]

I would say yes if you are actually using a diseque and you have chosen that in the menu then I would say get a new switch.A faulty switch will default to port 1, have you tried physically changing the cables in the other ports to see if they still work.Ports 2 and 4?
Thanks for reply Hunter11 , Yes , I checked the Diseqc port , I managed to scan it in by running the 119 directly to the receiver as Hutch suggested ,

Now only the sat I connect to diseqc 1 works , and it only works on diseqc 1 port on Both the switches I tried ,

so basically I can only watch one sat ....

Maybe Both switches are both Fried ???

suggestions? I have strong signal on both 119 and 110

[Hunter11]

Just a note here, if you don't power your reciever to the off position on the rear to cut power and you connect or disconnect your sat cable (rg6) from your switch (or Receiver) then you will blow your switch sure as shoot'n. You have up to 18 volts coming from your reciever to lnb with the switch in between. If you spike the switch you will blow it or blow the port on the switch. I always keep a spare swich handy, cuz when mine go it's always on a Sunday or holiday when stores are closed. lol.

[steiner01]

I would say yes if you are actually using a diseque and you have chosen that in the menu then I would say get a new switch.A faulty switch will default to port 1, have you tried physically changing the cables in the other ports to see if they still work.Ports 2 and 4?


Yes , I also tried ports 2 and 4 on both diseqc switches ....no luck ,,,

ok thanks , Im gonna go buy another switch today and see what happens ,,,,

[Glatt]

You probably have a bad LNB on 91

[anngreg]

Yes , I also tried ports 2 and 4 on both diseqc switches ....no luck ,,,

ok thanks , Im gonna go buy another switch today and see what happens ,,,,

you might want to try an older file also. sometimes that help too.